Crest Electronics CDVS-7000 Manuel d'utilisateur Page 23
- Page / 341
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
User Manual
i Series / iX Series 9
Parameter
Specification
Transient
Voltage: drop, step, sag, surge, sweep
Frequency: step, sag, surge, sweep
Voltage and Frequency: step, sweep
IEEE-488 Interface:
SH1, AH1, T6, L3, SR1, RL2, DC1, DT1
IEEE 488.2 and SCPI
Response time is 10 ms (typical)
RS232C Interface:
Bi-directional serial interface
9 pin D-shell connector
Handshake: CTS, RTS
Data bits: 7, 8
Stop bits: 1,2
Baud rate: 9600, 19200, 38400
IEEE 488.2 and SCPI
Current Limit Modes:
Two selectable modes of operation.
Constant current and constant voltage with hold-off time and trip.
Function Strobe
Isolated open collector output available between pin 31 (High) and pin
14 (Low) of the System Interface connector (J22). Negative going
pulse on any programmed voltage or frequency change.
Function strobe output can be reassigned as trigger output when
running list transients.
This output requires a external DC supply and pull-up resistor.
Remote Inhibit
Also referred to as Remote On/Off. Digital input available on pin 36
and pin 27 (D-Common) of the System Interface connector (J22). The
Remote inhibit input can be used to open the output relay. The output
relay state is not latching so will return to the closed state when the
input is removed.
2.1.8 Unit Protection
Input Overcurrent:
Circuit breaker with shunt trip control.
Input Overvoltage:
Automatic shunt trip of input circuit breaker.
Input Overvoltage
Transients:
Surge protection to withstand EN50082-1 (IEC 801-4, 5) levels.
Output Overcurrent:
Adjustable level constant current mode with a maximum set point
between 0% and 10% above programmed value.
Output Short Circuit:
Peak and rms current limit.
Overtemperature:
Automatic shutdown.
- AC Power Source 1
- User Manual 1
- SAFETY SYMBOLS 7
- 1. Introduction 15
- 2. Specifications 16
- 2.2 Mechanical 24
- 2.3 Environmental 24
- 2.4 Regulatory 26
- 2.5 Front Panel Controls 26
- 3.1 Unpacking 29
- 3.2 Power Requirements 29
- 3.3 Mechanical Installation 30
- 3.4 Input Wiring – TB1 30
- 3.6 Connectors - Rear Panel 32
- Description 33
- Centronics 36
- Connector 36
- > 400 uS 36
- 24 i Series / iX Series 38
- 3.8 Output Voltage Ranges 40
- 3.9 Functional Test 41
- 28 i Series / iX Series 42
- 30 i Series / iX Series 44
- 34 i Series / iX Series 48
- 4. Front Panel Operation 51
- FUNCTION 53
- 4.2 Menu Structure 56
- 44 i Series / iX Series 58
- 4.2.2 Overview of Menu 1 58
- 4.3 Output Programming 91
- 4.5 Standard Measurements 97
- 4.7 Transient Programming 108
- 5. Principle of Operation 115
- 5.2 Overall Description 116
- 5.3 Oscillator Assembly 116
- 104 i Series / iX Series 118
- 5.4 Current Limit Board 119
- 5.5 Auxiliary Power Supply 119
- 5.6 DC-DC Power Converter 120
- 5.7 AC Control Logic 120
- 108 i Series / iX Series 122
- 5.8 AC Power Board 123
- 5.9 Input/Output Board 123
- 110 i Series / iX Series 124
- CAUTION 126
- 6. Calibration 127
- 118 i Series / iX Series 132
- 6.6 Non-Routine Calibration 134
- 124 i Series / iX Series 138
- 7. Service 139
- 9. Options 147
- 138 i Series / iX Series 152
- Refer to 157
- 158 i Series / iX Series 172
- 9.1.2.8 160 Test Selection 172
- 164 i Series / iX Series 178
- 168 i Series / iX Series 182
- 170 i Series / iX Series 184
- 172 i Series / iX Series 186
- 174 i Series / iX Series 188
- 176 i Series / iX Series 190
- 178 i Series / iX Series 192
- 9.2 IEC 61000-4-11 Option 194
- 9.3 IEC 61000-4-13 Option 201
- 196 i Series / iX Series 210
- 9.4 EOS Option 213
- 206 i Series / iX Series 220
- 208 i Series / iX Series 222
- Figure 9-39: 15003iX/3-EOS3 222
- 9.5 Mode iX Option 228
- 218 i Series / iX Series 232
- 9.6 Omni Options 236
- 226 i Series / iX Series 240
- 228 i Series / iX Series 242
- Power Switch and Lamp 244
- 80-250V SYNC INPUT FROM iX 250
- SOURCE INPUT,OR 250
- OTHER AC LINE VOLTAGE 250
- 9.8.2.8 704 Test Selection 273
- 260 i Series / iX Series 274
- 262 i Series / iX Series 276
- 266 i Series / iX Series 280
- 268 i Series / iX Series 282
- 270 i Series / iX Series 284
- 272 i Series / iX Series 286
- 274 i Series / iX Series 288
- 276 i Series / iX Series 290
- 278 i Series / iX Series 292
- 280 i Series / iX Series 294
- 282 i Series / iX Series 296
- 284 i Series / iX Series 298
- 286 i Series / iX Series 300
- 9.9.7 ABD Test Selection 309
- 296 i Series / iX Series 310
- 298 i Series / iX Series 312
- 302 i Series / iX Series 316
- Controls 319
- 308 i Series / iX Series 322
- 310 i Series / iX Series 324
- 312 i Series / iX Series 326
- 314 i Series / iX Series 328
- 9.10 WHM Option 331
- 10. Error Messages 334
- 322 i Series / iX Series 336
- 324 i Series / iX Series 338
- Table 10-1: Error Messages 338
- 11. Index 339
Produits connexes et manuels pour Enregistreurs vidéo numériques (DVR) Crest Electronics CDVS-7000
(30 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels